| These specifications describe a self-contained patch unit which is a "slide in" unit to be used for patching with hot asphalt.
CONTAINER
The unit shall be 4 cubic yards.
Double wall constructed.
2" - 6 lb. density insulation throughout.
10 GA HR steel interior sides, 12 GA HR steel exterior.
The floor shall be 1/4 inch HR steel.
Interior walls of loading lids have expansion corrugations.
Top loading doors are 2" double wall constructed.
Flame cut upper pivot arms for top lids.
All doors hydraulically operate by 2" x 11" stroke cylinders.
Material funneled to center of container.
Hydraulic controls located at right rear corner.
Hydraulic system is powered by an 8 H.P. LPG engine.
Starter generator with 12 volt, 50 AMP battery.
Hydraulic controls located at the right rear corner.
Width of box is 74" O.D.
Length of box is 132" O.D.
Patcher is designed to fit into 10 ft. dump body.
RADIANT HEATER
Heat tubes located under the container.
Interior heat chamber has passage ways to direct heat.
Passage ways separate from heat chamber.
Chamber totally enclosed inside container.
Burners propane fueled.
Rating of 67,000 BTU each @ pressure of 5 PSI.
Controlled by thermostat range of 100° to 300° F.
12 volt electronic ignitors.
100% fuel shut off if flame is extinguished.
Burner area fully enclosed.
LOADING AND UNLOADING
Patcher shall have free standing legs.
Shall be loaded and unloaded from the truck dump body without ancillary equipment.
SHOVELING APRON - MODEL 10
Constructed of 10 GA HR steel.
Folding bottom for material to bypass freely.
Mounted on rear of container.
1/4 cubic yard capacity.
LPG TANK
25 gallon upright (portable) tank.
OPTIONAL EQUIPMENT
HAND TORCH
Pilot with valve control.
Capacity of 200,000 BTU.
25 foot hose supplied.
EMULSION SPRAY UNIT
Emulsified Asphalt spray and storage system mounted on truck chassis for applying tack coat.
Tank
Two compartment tank.
Storage capacity 24 gallon emulsion and 6 gallon solvent.
10 gauge steel with the bottom reinforced.
6" curbside filler cap.
Tank shall be vented.
Removable fill basket strainer.
Y strainer at the discharge of tank before material enters the pump.
Capable of switching from emulsion to solvent with one valve lever.
Auxiliary Electric Heat
Equipped with 110 VAC heat system.
Over night heating, controlled by temperature sensor.
Heating elements shall be low density stainless steel.
Mounting
Sprayer shall be mounted in front of patcher body.
Pump
Rotary gear pump.
Output of 10 gallons per minute of 600 R.P.M.
Pump shall be hydraulic driven.
All valves shall be high pressure.
It shall be remote mounted for ease of maintenance.
Mechanically actuated from the right rear of the body.
Pump shall be reversible to draw material back to tank.
Pump shall be driven by a torque motor which has 5.9 CID.
Spray Wand And Hose
System should be plumped to curbside rear of truck.
3/8 inch diameter 5 feet long steel application wand shall be supplied.
25 feet of 1/2 inch diameter oil resistant hose.
A brass changeable nozzle at spray tip.
Wand storage brackets.
AUXILIARY ELECTRIC HEAT PATCHER
Low density electric heat.
Minimum 6KW, 240 VAC thermostatically controlled.
100°F to 300°F.
Rain tight control panel.
Overnight heating of asphalt.
HOSE REELS
Emulsion spray hose reel.
Hand torch hose reel.
Solvent hose reel.
All reels are designed to accommodate 25 foot hoses.
ARROWBOARD
(10) light board.
Arrow - left, right, or both.
Mounted at rear of unit.
THERMOMETER
0 - 300°F
FIRE EXTINGUISHER
5 lbs., 10 lbs.
STROBE LIGHTS & BEACONS
RE-EMULSIFYING SYSTEM
HYDRAULIC TOOL CIRCUIT
AIR TYPE EMULSION SPRAY SYSTEMS
|
